telnetd(8)
TELNETD(8) UNIX System Manager's Manual TELNETD(8)
NAME
telnetd - DARPA TELNET protocol server
SYNOPSIS
telnetd [-BUhkln] [-D debugmode] [-S tos] [-X authtype] [-a authmode]
[-rlowpty-highpty] [-u len] [-debug] [-L /bin/login] [-y] [port]
DESCRIPTION
The telnetd command is a server which supports the DARPA standard TELNET
virtual terminal protocol. Telnetd is normally invoked by the internet
server (see inetd(8)) for requests to connect to the TELNET port as in-
dicated by the /etc/services file (see services(5)). The -debug option
may be used to start up telnetd manually, instead of through inetd(8).
If started up this way, port may be specified to run telnetd on an alter-
nate TCP port number.
The telnetd command accepts the following options:
-a authmode This option may be used for specifying what mode should be
used for authentication. Note that this option is only use-
ful if telnetd has been compiled with support for the
AUTHENTICATION option. There are several valid values for
authmode:
debug Turns on authentication debugging code.
user Only allow connections when the remote user can pro-
vide valid authentication information to identify the
remote user, and is allowed access to the specified
account without providing a password.
valid Only allow connections when the remote user can pro-
vide valid authentication information to identify the
remote user. The login(1) command will provide any
additional user verification needed if the remote us-
er is not allowed automatic access to the specified
account.
other Only allow connections that supply some authentica-
tion information. This option is currently not sup-
ported by any of the existing authentication mecha-
nisms, and is thus the same as specifying -a valid.
otp Only allow authenticated connections (as with -a
user) and also logins with one-time passwords (OTPs).
This option will call login with an option so that
only OTPs are accepted. The user can of course still
type secret information at the prompt.
none This is the default state. Authentication informa-
tion is not required. If no or insufficient authen-
tication information is provided, then the login(1)
program will provide the necessary user verification.
off This disables the authentication code. All user ver-
ification will happen through the login(1) program.
-B Ignored.
-D debugmode
This option may be used for debugging purposes. This allows
telnetd to print out debugging information to the connec-
tion, allowing the user to see what telnetd is doing. There
are several possible values for debugmode:
options Prints information about the negotiation of TELNET
options.
report Prints the options information, plus some addi-
tional information about what processing is going
on.
netdata Displays the data stream received by telnetd.
ptydata Displays data written to the pty.
exercise Has not been implemented yet.
-h Disables the printing of host-specific information before
login has been completed.
-k
-l Ignored.
-n Disable TCP keep-alives. Normally telnetd enables the TCP
keep-alive mechanism to probe connections that have been
idle for some period of time to determine if the client is
still there, so that idle connections from machines that
have crashed or can no longer be reached may be cleaned up.
-r lowpty-highpty
This option is only enabled when telnetd is compiled for
UNICOS. It specifies an inclusive range of pseudo-terminal
devices to use. If the system has sysconf variable
_SC_CRAY_NPTY configured, the default pty search range is 0
to _SC_CRAY_NPTY; otherwise, the default range is 0 to 128.
Either lowpty or highpty may be omitted to allow changing
either end of the search range. If lowpty is omitted, the -
character is still required so that telnetd can differenti-
ate highpty from lowpty.
-S tos
-u len This option is used to specify the size of the field in the
utmp structure that holds the remote host name. If the re-
solved host name is longer than len, the dotted decimal val-
ue will be used instead. This allows hosts with very long
host names that overflow this field to still be uniquely
identified. Specifying -u0 indicates that only dotted deci-
mal addresses should be put into the utmp file.
-U This option causes telnetd to refuse connections from ad-
dresses that cannot be mapped back into a symbolic name via
the gethostbyaddr(3) routine.
-X authtype This option is only valid if telnetd has been built with
support for the authentication option. It disables the use
of authtype authentication, and can be used to temporarily
disable a specific authentication type without having to re-
compile telnetd.
-L pathname Specify pathname to an alternative login program.
-y Makes telnetd not warn when a user is trying to login with a
cleartext password.
Telnetd operates by allocating a pseudo-terminal device (see pty(4)) for
a client, then creating a login process which has the slave side of the
pseudo-terminal as stdin, stdout and stderr. Telnetd manipulates the mas-
ter side of the pseudo-terminal, implementing the TELNET protocol and
passing characters between the remote client and the login process.
When a TELNET session is started up, telnetd sends TELNET options to the
client side indicating a willingness to do the following TELNET options,
which are described in more detail below:
DO AUTHENTICATION
WILL ENCRYPT
DO TERMINAL TYPE
DO TSPEED
DO XDISPLOC
DO NEW-ENVIRON
DO ENVIRON
WILL SUPPRESS GO AHEAD
DO ECHO
DO LINEMODE
DO NAWS
WILL STATUS
DO LFLOW
DO TIMING-MARK
The pseudo-terminal allocated to the client is configured to operate in
``cooked'' mode, and with XTABS and CRMOD enabled (see tty(4)).
Telnetd has support for enabling locally the following TELNET options:
WILL ECHO When the LINEMODE option is enabled, a WILL ECHO or
WONT ECHO will be sent to the client to indicate the
current state of terminal echoing. When terminal echo
is not desired, a WILL ECHO is sent to indicate that
telnetd will take care of echoing any data that needs
to be echoed to the terminal, and then nothing is
echoed. When terminal echo is desired, a WONT ECHO is
sent to indicate that telnetd will not be doing any
terminal echoing, so the client should do any terminal
echoing that is needed.
WILL BINARY Indicates that the client is willing to send a 8 bits
of data, rather than the normal 7 bits of the Network
Virtual Terminal.
WILL SGA Indicates that it will not be sending IAC GA, go
ahead, commands.
WILL STATUS Indicates a willingness to send the client, upon re-
quest, of the current status of all TELNET options.
WILL TIMING-MARK Whenever a DO TIMING-MARK command is received, it is
always responded to with a WILL TIMING-MARK
WILL LOGOUT When a DO LOGOUT is received, a WILL LOGOUT is sent in
response, and the TELNET session is shut down.
WILL ENCRYPT Only sent if telnetd is compiled with support for data
encryption, and indicates a willingness to decrypt the
data stream.
Telnetd has support for enabling remotely the following TELNET options:
DO BINARY Sent to indicate that telnetd is willing to receive an
8 bit data stream.
DO LFLOW Requests that the client handle flow control charac-
ters remotely.
DO ECHO This is not really supported, but is sent to identify
a 4.2BSD telnet(1) client, which will improperly re-
spond with WILL ECHO. If a WILL ECHO is received, a
DONT ECHO will be sent in response.
DO TERMINAL-TYPE Indicates a desire to be able to request the name of
the type of terminal that is attached to the client
side of the connection.
DO SGA Indicates that it does not need to receive IAC GA, the
go ahead command.
DO NAWS Requests that the client inform the server when the
window (display) size changes.
DO TERMINAL-SPEED Indicates a desire to be able to request information
about the speed of the serial line to which the client
is attached.
DO XDISPLOC Indicates a desire to be able to request the name of
the X windows display that is associated with the tel-
net client.
DO NEW-ENVIRON Indicates a desire to be able to request environment
variable information, as described in RFC 1572.
DO ENVIRON Indicates a desire to be able to request environment
variable information, as described in RFC 1408.
DO LINEMODE Only sent if telnetd is compiled with support for
linemode, and requests that the client do line by line
processing.
DO TIMING-MARK Only sent if telnetd is compiled with support for both
linemode and kludge linemode, and the client responded
with WONT LINEMODE. If the client responds with WILL
TM, the it is assumed that the client supports kludge
linemode. Note that the [-k] option can be used to
disable this.
DO AUTHENTICATION Only sent if telnetd is compiled with support for au-
thentication, and indicates a willingness to receive
authentication information for automatic login.
DO ENCRYPT Only sent if telnetd is compiled with support for data
encryption, and indicates a willingness to decrypt the
data stream.
FILES
/etc/services
/etc/inittab (UNICOS systems only)
/etc/iptos (if supported)
SEE ALSO
telnet(1), login(1)
STANDARDS
RFC-854 TELNET PROTOCOL SPECIFICATION
RFC-855 TELNET OPTION SPECIFICATIONS
RFC-856 TELNET BINARY TRANSMISSION
RFC-857 TELNET ECHO OPTION
RFC-858 TELNET SUPPRESS GO AHEAD OPTION
RFC-859 TELNET STATUS OPTION
RFC-860 TELNET TIMING MARK OPTION
RFC-861 TELNET EXTENDED OPTIONS - LIST OPTION
RFC-885 TELNET END OF RECORD OPTION
RFC-1073 Telnet Window Size Option
RFC-1079 Telnet Terminal Speed Option
RFC-1091 Telnet Terminal-Type Option
RFC-1096 Telnet X Display Location Option
RFC-1123 Requirements for Internet Hosts -- Application and Support
RFC-1184 Telnet Linemode Option
RFC-1372 Telnet Remote Flow Control Option
RFC-1416 Telnet Authentication Option
RFC-1411 Telnet Authentication: Kerberos Version 4
RFC-1412 Telnet Authentication: SPX
RFC-1571 Telnet Environment Option Interoperability Issues
RFC-1572 Telnet Environment Option
BUGS
Some TELNET commands are only partially implemented.
Because of bugs in the original 4.2 BSD telnet(1), telnetd performs some
dubious protocol exchanges to try to discover if the remote client is, in
fact, a 4.2 BSD telnet(1).
Binary mode has no common interpretation except between similar operating
systems (Unix in this case).
The terminal type name received from the remote client is converted to
lower case.
Telnetd never sends TELNET IAC GA (go ahead) commands.
4.2 Berkeley Distribution June 1, 1994 5
Man(1) output converted with
man2html